VOLVO
ECM-P230412 - Ignition Coil B Primary Control Circuit High. General Electrical Failures. Circuit short to battery
System
Engine Control Module (ECM)
Volvo models this fault code applies to
Applies to the following models:
7 modelsS60 (2011–), S80 (2007–), V40 (2013–), V40 Cross Country (2013–), V60 (2011–), V70 (2008–), XC60 (2009–)
Show models by year and engine (20)
- Volvo S60 (2011–)2011Engine B4164T, B4164T3, B4204T6, B4204T7 only
- Volvo S60 (2011–)2012–2014Engine B4164T, B4164T2, B4164T3, B4204T7 only
- Volvo S60 (2011–)2015Engine B4164T, B4164T2, B4164T3 only
- Volvo S80 (2007–)2010Engine B4204T6 only
- Volvo S80 (2007–)2011Engine B4164T, B4204T6, B4204T7 only
- Volvo S80 (2007–)2012–2014Engine B4164T, B4164T2, B4204T6, B4204T7 only
- Volvo S80 (2007–)2015Engine B4164T only
- Volvo V40 (2013–)2013Engine B4164T, B4164T3 only
- Volvo V40 (2013–)2014–2015Engine B4164T, B4164T3, B4164T4 only
- Volvo V40 Cross Country (2013–)2013–2015Engine B4164T only
- Volvo V60 (2011–)2011Engine B4164T, B4164T3, B4204T6, B4204T7 only
- Volvo V60 (2011–)2012–2014Engine B4164T, B4164T2, B4164T3, B4204T7 only
- Volvo V60 (2011–)2015Engine B4164T, B4164T2, B4164T3 only
- Volvo V70 (2008–)2010Engine B4204T6 only
- Volvo V70 (2008–)2011Engine B4164T, B4204T6, B4204T7 only
- Volvo V70 (2008–)2012–2014Engine B4164T, B4164T2, B4204T7 only
- Volvo V70 (2008–)2015Engine B4164T, B4164T2 only
- Volvo XC60 (2009–)2010Engine B4204T6 only
- Volvo XC60 (2009–)2011–2012Engine B4204T6, B4204T7 only
- Volvo XC60 (2009–)2013–2015Engine B4204T7 only
What does this fault code mean?
The engine control module (ECM) monitors the signal line to the ignition coil primary winding. The code is set when the signal is too high, which in this case means the signal line to ignition coil 2 has been short-circuited to supply voltage. It is an electrical fault in the circuit, and the code applies only to this ignition coil.
Possible causes
- The signal wire to ignition coil 2 is short-circuited to supply voltage
- The ignition coil is damaged
What you can do
- 1Check that the relevant fuses are intact; their locations are shown in the car's owner's manual
- 2Read and note the code, clear it and run the engine for a while to see whether it returns
- 3Inspect the connector and cable at ignition coil 2 for loose contacts, corrosion, chafing and pinching
- 4Use a multimeter to check that the signal wire to ignition coil 2 has no contact with supply voltage
- 5If the fault returns, have a workshop with diagnostic equipment check the ignition coil and its wiring
Symptoms you may notice2
- The engine warning lamp (Check engine) lights up or behaves abnormally
- The car runs poorly and lacks power
General guidance for car owners. Diagnosis on the car can point to a different cause.