VOLVO
ECM-P230911 - Ignition Coil D Primary Control Circuit Low. General Electrical Failures. Circuit short to ground
System
Engine Control Module (ECM)
Volvo models this fault code applies to
Applies to the following models:
7 modelsS60 (2011–), S80 (2007–), V40 (2013–), V40 Cross Country (2013–), V60 (2011–), V70 (2008–), XC60 (2009–)
Show models by year and engine (20)
- Volvo S60 (2011–)2011Engine B4164T, B4164T3, B4204T6, B4204T7 only
- Volvo S60 (2011–)2012–2014Engine B4164T, B4164T2, B4164T3, B4204T7 only
- Volvo S60 (2011–)2015Engine B4164T, B4164T2, B4164T3 only
- Volvo S80 (2007–)2010Engine B4204T6 only
- Volvo S80 (2007–)2011Engine B4164T, B4204T6, B4204T7 only
- Volvo S80 (2007–)2012–2014Engine B4164T, B4164T2, B4204T6, B4204T7 only
- Volvo S80 (2007–)2015Engine B4164T only
- Volvo V40 (2013–)2013Engine B4164T, B4164T3 only
- Volvo V40 (2013–)2014–2015Engine B4164T, B4164T3, B4164T4 only
- Volvo V40 Cross Country (2013–)2013–2015Engine B4164T only
- Volvo V60 (2011–)2011Engine B4164T, B4164T3, B4204T6, B4204T7 only
- Volvo V60 (2011–)2012–2014Engine B4164T, B4164T2, B4164T3, B4204T7 only
- Volvo V60 (2011–)2015Engine B4164T, B4164T2, B4164T3 only
- Volvo V70 (2008–)2010Engine B4204T6 only
- Volvo V70 (2008–)2011Engine B4164T, B4204T6, B4204T7 only
- Volvo V70 (2008–)2012–2014Engine B4164T, B4164T2, B4204T7 only
- Volvo V70 (2008–)2015Engine B4164T, B4164T2 only
- Volvo XC60 (2009–)2010Engine B4204T6 only
- Volvo XC60 (2009–)2011–2012Engine B4204T6, B4204T7 only
- Volvo XC60 (2009–)2013–2015Engine B4204T7 only
What does this fault code mean?
The engine control module (ECM) measures the signal to ignition coil 4 and sets the code when it is too low. This means the signal wire has been short-circuited to ground. The fault is electrical and applies only to this ignition coil.
Possible causes
- Short circuit to ground in the signal wire to ignition coil 4
- The ignition coil is damaged
What you can do
- 1The fuses should be intact; see the car's owner's manual for where they are
- 2Read and clear the code, test drive and see whether it returns
- 3Check the connector at ignition coil 4 for loose contacts and corrosion
- 4Use a multimeter to check that the signal wire to ignition coil 4 has no contact with ground (the body)
- 5Follow the wiring harness and look for chafing and pinched sections, especially at clips and grommets
- 6If the fault returns, have a workshop with diagnostic equipment check the ignition coil and the wiring
Symptoms you may notice2
- The engine warning lamp (Check engine) lights up or behaves abnormally
- The car runs poorly and lacks power
General guidance for car owners. Diagnosis on the car can point to a different cause.