VOLVO
ECM-P250C12 - Engine Oil Level Sensor Circuit Low. General Electrical Failures. Circuit short to battery
System
Engine Control Module (ECM)
Volvo models this fault code applies to
Applies to the following models:
7 modelsS60 (2011–), S80 (2007–), V40 (2013–), V40 Cross Country (2013–), V60 (2011–), V70 (2008–), XC60 (2009–)
Show models by year and engine (20)
- Volvo S60 (2011–)2011Engine B4164T, B4164T3, B4204T6, B4204T7 only
- Volvo S60 (2011–)2012–2014Engine B4164T, B4164T2, B4164T3, B4204T7 only
- Volvo S60 (2011–)2015Engine B4164T, B4164T2, B4164T3 only
- Volvo S80 (2007–)2010Engine B4204T6 only
- Volvo S80 (2007–)2011Engine B4164T, B4204T6, B4204T7 only
- Volvo S80 (2007–)2012–2014Engine B4164T, B4164T2, B4204T6, B4204T7 only
- Volvo S80 (2007–)2015Engine B4164T only
- Volvo V40 (2013–)2013Engine B4164T, B4164T3 only
- Volvo V40 (2013–)2014–2015Engine B4164T, B4164T3, B4164T4 only
- Volvo V40 Cross Country (2013–)2013–2015Engine B4164T only
- Volvo V60 (2011–)2011Engine B4164T, B4164T3, B4204T6, B4204T7 only
- Volvo V60 (2011–)2012–2014Engine B4164T, B4164T2, B4164T3, B4204T7 only
- Volvo V60 (2011–)2015Engine B4164T, B4164T2, B4164T3 only
- Volvo V70 (2008–)2010Engine B4204T6 only
- Volvo V70 (2008–)2011Engine B4164T, B4204T6, B4204T7 only
- Volvo V70 (2008–)2012–2014Engine B4164T, B4164T2, B4204T7 only
- Volvo V70 (2008–)2015Engine B4164T, B4164T2 only
- Volvo XC60 (2009–)2010Engine B4204T6 only
- Volvo XC60 (2009–)2011–2012Engine B4204T6, B4204T7 only
- Volvo XC60 (2009–)2013–2015Engine B4204T7 only
What does this fault code mean?
The ECM measures the voltage across the oil level sensor, whose resistance changes with the oil level. The code is stored when the control module detects a fault in that measurement. Possible causes are poor contact, a signal wire shorted to ground, an oil level that is too low or a damaged sensor.
Possible causes
- Contact resistance or oxidation in the connections
- Signal wire short-circuited to ground
- Oil level too low
- Damaged oil level sensor
What you can do
- 1Check the oil level with the dipstick. If it is too low, top up with the correct oil
- 2Check that the relevant fuses are intact
- 3Check the connector to the oil level sensor for contact resistance and oxidation
- 4Use a multimeter to check that the signal wire from the oil level sensor is not shorted to plus and not to ground (body)
- 5If the fault remains after these checks, have a workshop with diagnostic equipment check the oil level sensor
Symptoms you may notice1
- No noticeable symptoms for the driver
General guidance for car owners. Diagnosis on the car can point to a different cause.