VOLVO
ECM-P254217 - Low Pressure Fuel System Sensor Circuit High. General Electrical Failures. Circuit voltage above threshold
System
Engine Control Module (ECM)
Volvo models this fault code applies to
Applies to the following models:
7 modelsS60 (2011–), S80 (2007–), V40 (2013–), V40 Cross Country (2013–), V60 (2011–), V70 (2008–), XC60 (2009–)
Show models by year and engine (20)
- Volvo S60 (2011–)2011Engine B4164T, B4164T3, B4204T6, B4204T7 only
- Volvo S60 (2011–)2012–2014Engine B4164T, B4164T2, B4164T3, B4204T7 only
- Volvo S60 (2011–)2015Engine B4164T, B4164T2, B4164T3 only
- Volvo S80 (2007–)2010Engine B4204T6 only
- Volvo S80 (2007–)2011Engine B4164T, B4204T6, B4204T7 only
- Volvo S80 (2007–)2012–2014Engine B4164T, B4164T2, B4204T6, B4204T7 only
- Volvo S80 (2007–)2015Engine B4164T only
- Volvo V40 (2013–)2013Engine B4164T, B4164T3 only
- Volvo V40 (2013–)2014–2015Engine B4164T, B4164T3, B4164T4 only
- Volvo V40 Cross Country (2013–)2013–2015Engine B4164T only
- Volvo V60 (2011–)2011Engine B4164T, B4164T3, B4204T6, B4204T7 only
- Volvo V60 (2011–)2012–2014Engine B4164T, B4164T2, B4164T3, B4204T7 only
- Volvo V60 (2011–)2015Engine B4164T, B4164T2, B4164T3 only
- Volvo V70 (2008–)2010Engine B4204T6 only
- Volvo V70 (2008–)2011Engine B4164T, B4204T6, B4204T7 only
- Volvo V70 (2008–)2012–2014Engine B4164T, B4164T2, B4204T7 only
- Volvo V70 (2008–)2015Engine B4164T, B4164T2 only
- Volvo XC60 (2009–)2010Engine B4204T6 only
- Volvo XC60 (2009–)2011–2012Engine B4204T6, B4204T7 only
- Volvo XC60 (2009–)2013–2015Engine B4204T7 only
What does this fault code mean?
The fuel pressure sensor on the low-pressure side, just before the high-pressure pump, sends a signal to the engine control module. The code is stored when the signal is too high. Possible causes are poor contact, a signal wire shorted to supply voltage, an open circuit in the signal or ground wire, or a damaged sensor.
Possible causes
- Poor or oxidised terminals and connections
- Signal wire short-circuited to supply voltage
- Open circuit in the signal wire
- Open circuit in the signal ground wire
- Damaged low-pressure fuel pressure sensor
What you can do
- 1Start the engine, warm it up and read the fault status; if the fault is not active, it may have been intermittent
- 2Check the connector of the fuel pressure sensor for contact resistance and oxidation; clean and remedy it if needed
- 3Use a multimeter to check that the signal wire is not shorted to plus and has no open circuit
- 4Use a multimeter to check that the ground wire to the sensor has no open circuit
- 5If the fault remains, have a workshop with diagnostic equipment check the fuel pressure sensor
Symptoms you may notice1
- The Check engine lamp comes on or behaves abnormally
General guidance for car owners. Diagnosis on the car can point to a different cause.