VOLVO
ECM-U011181 - Lost Communication With Battery Energy Control Module "A". Bus Signal / Message Failures. Invalid serial data received
System
Engine Control Module (ECM)
Volvo models this fault code applies to
Applies to the following models:
7 modelsS60 (2011–), S80 (2007–), V40 (2013–), V40 Cross Country (2013–), V60 (2011–), V70 (2008–), XC60 (2009–)
Show models by year and engine (20)
- Volvo S60 (2011–)2011Engine B4164T, B4164T3, B4204T6, B4204T7 only
- Volvo S60 (2011–)2012–2014Engine B4164T, B4164T2, B4164T3, B4204T7 only
- Volvo S60 (2011–)2015Engine B4164T, B4164T2, B4164T3 only
- Volvo S80 (2007–)2010Engine B4204T6 only
- Volvo S80 (2007–)2011Engine B4164T, B4204T6, B4204T7 only
- Volvo S80 (2007–)2012–2014Engine B4164T, B4164T2, B4204T6, B4204T7 only
- Volvo S80 (2007–)2015Engine B4164T only
- Volvo V40 (2013–)2013Engine B4164T, B4164T3 only
- Volvo V40 (2013–)2014–2015Engine B4164T, B4164T3, B4164T4 only
- Volvo V40 Cross Country (2013–)2013–2015Engine B4164T only
- Volvo V60 (2011–)2011Engine B4164T, B4164T3, B4204T6, B4204T7 only
- Volvo V60 (2011–)2012–2014Engine B4164T, B4164T2, B4164T3, B4204T7 only
- Volvo V60 (2011–)2015Engine B4164T, B4164T2, B4164T3 only
- Volvo V70 (2008–)2010Engine B4204T6 only
- Volvo V70 (2008–)2011Engine B4164T, B4204T6, B4204T7 only
- Volvo V70 (2008–)2012–2014Engine B4164T, B4164T2, B4204T7 only
- Volvo V70 (2008–)2015Engine B4164T, B4164T2 only
- Volvo XC60 (2009–)2010Engine B4204T6 only
- Volvo XC60 (2009–)2011–2012Engine B4204T6, B4204T7 only
- Volvo XC60 (2009–)2013–2015Engine B4204T7 only
What does this fault code mean?
The engine control module (ECM) constantly receives data over the CAN network from the central electronics control module (CEM). The code is set when the engine control module detects faulty CAN communication. Although the code is titled lost communication with the battery energy control module “A”, it applies to the CAN communication between the engine control module and the central electronics control module.
Possible causes
- Fault in the central electronics control module (CEM)
- Intermittent breaks in one or both CAN wires
- Intermittent short circuits between the CAN wires, or between a CAN wire and ground or supply voltage
- The sending control module has stopped sending the signal the engine control module expects
- Incorrect signal configuration in a control module that was replaced without new software being loaded
What you can do
- 1Read the codes in the engine control module and first fix any other CAN-related codes, as they may share the same cause
- 2Clear the code and road test the car to see if it is set again
- 3Check the CAN wiring between the engine control module and the central electronics control module for chafing, pinched areas and loose connectors
- 4Use a multimeter to check that the CAN wires have no break and are not shorted to ground or supply voltage
- 5Check that the battery has good voltage and that the fuses are intact
- 6If the fault returns: have a workshop with diagnostic equipment check the central electronics control module. Do not work on the battery system yourself
Symptoms you may notice1
- No noticeable symptoms for the driver
General guidance for car owners. Diagnosis on the car can point to a different cause.