VOLVO
ECM-U200581 - Vehicle Speed. Bus Signal / Message Failures. Invalid serial data received
System
Engine Control Module (ECM)
Volvo models this fault code applies to
Applies to the following models:
7 modelsS60 (2011–), S80 (2007–), V40 (2013–), V40 Cross Country (2013–), V60 (2011–), V70 (2008–), XC60 (2009–)
Show models by year and engine (20)
- Volvo S60 (2011–)2011Engine B4164T, B4164T3, B4204T6, B4204T7 only
- Volvo S60 (2011–)2012–2014Engine B4164T, B4164T2, B4164T3, B4204T7 only
- Volvo S60 (2011–)2015Engine B4164T, B4164T2, B4164T3 only
- Volvo S80 (2007–)2010Engine B4204T6 only
- Volvo S80 (2007–)2011Engine B4164T, B4204T6, B4204T7 only
- Volvo S80 (2007–)2012–2014Engine B4164T, B4164T2, B4204T6, B4204T7 only
- Volvo S80 (2007–)2015Engine B4164T only
- Volvo V40 (2013–)2013Engine B4164T, B4164T3 only
- Volvo V40 (2013–)2014–2015Engine B4164T, B4164T3, B4164T4 only
- Volvo V40 Cross Country (2013–)2013–2015Engine B4164T only
- Volvo V60 (2011–)2011Engine B4164T, B4164T3, B4204T6, B4204T7 only
- Volvo V60 (2011–)2012–2014Engine B4164T, B4164T2, B4164T3, B4204T7 only
- Volvo V60 (2011–)2015Engine B4164T, B4164T2, B4164T3 only
- Volvo V70 (2008–)2010Engine B4204T6 only
- Volvo V70 (2008–)2011Engine B4164T, B4204T6, B4204T7 only
- Volvo V70 (2008–)2012–2014Engine B4164T, B4164T2, B4204T7 only
- Volvo V70 (2008–)2015Engine B4164T, B4164T2 only
- Volvo XC60 (2009–)2010Engine B4204T6 only
- Volvo XC60 (2009–)2011–2012Engine B4204T6, B4204T7 only
- Volvo XC60 (2009–)2013–2015Engine B4204T7 only
What does this fault code mean?
The engine control module (ECM) receives the vehicle speed from the brake control module (BCM) over CAN. The code is set when an expected message from the BCM is missing. The fault may lie in the CAN connections, in the wiring, or in either of the two control modules.
Possible causes
- Contact resistance in the CAN connections
- Open circuit in one or both CAN cables
- One or both signal cables are short-circuited to ground, to voltage or to each other
- Damaged brake control module (BCM)
- Damaged engine control module (ECM)
What you can do
- 1Read the fault codes in the engine control module. If any of ECM-U012088, ECM-U000188, ECM-U1A1400, ECM-U000108 or ECM-U000100 is stored, investigate it first.
- 2Read the fault codes in the brake control module (BCM). Any communication faults there should be investigated first, as this code is then a follow-on fault.
- 3Check that the connectors in the CAN network between the BCM and the engine control module are secure and clean, and look for chafed wiring.
- 4Do not work on the brake system yourself. Have a workshop check the BCM if the code returns.
Symptoms you may notice1
- The check engine lamp lights up or behaves abnormally
What the fault can affect1
- The BCM's speed signal is replaced by a substitute value
General guidance for car owners. Diagnosis on the car can point to a different cause.