VOLVO
TCM-029A - Transmission control module (TCM). Internal fault
System
Transmission Control Module (TCM)
Volvo models this fault code applies to
Applies to the following models:
8 modelsC30 (2007–2013), C70 (2006–2013), S40 (2004–2013), S60 (2001–2009), V50 (2004–2013), V70 (2000–2008), V70 XC / XC70 (2001–2007), XC90 (2003–)
Show models by year and engine (15)
- Volvo C30 (2007–2013)2007–2013Transmission AW55-50/51SN only
- Volvo C70 (2006–2013)2006–2013Transmission AW55-50/51SN only
- Volvo S40 (2004–2013)2004, 2011–2012Transmission AW55-50/51SN only
- Volvo S40 (2004–2013)2005–2010Transmission AW50/51 AWD, AW55-50/51SN only
- Volvo S60 (2001–2009)2006–2007Engine B5254T4, D5244T4, D5244T5 only · Transmission TF-80SC, TF-80SC AWD only
- Volvo S60 (2001–2009)2008–2009Engine D5244T4, D5244T5 only · Transmission TF-80SC only
- Volvo V50 (2004–2013)2004, 2011–2012Transmission AW55-50/51SN only
- Volvo V50 (2004–2013)2005–2010Transmission AW50/51 AWD, AW55-50/51SN only
- Volvo V70 (2000–2008)2006–2007Engine B5254T4, D5244T4, D5244T5 only · Transmission TF-80SC, TF-80SC AWD only
- Volvo V70 (2000–2008)2008Engine D5244T5 only · Transmission TF-80SC only
- Volvo V70 XC / XC70 (2001–2007)2006–2007Engine D5244T4 only · Transmission TF-80SC AWD only
- Volvo XC90 (2003–)2006–2007Engine D5244T4 only · Transmission TF-80SC AWD only
- Volvo XC90 (2003–)2008–2010Engine D5244T4, D5244T5 only · Transmission TF-80SC AWD only
- Volvo XC90 (2003–)2011Engine D5244T18, D5244T4, D5244T5 only · Transmission TF-80SC, TF-80SC AWD only
- Volvo XC90 (2003–)2012All engines except: B5254T2, B6324S5 · All transmissions except: AW50/51 AWD
What does this fault code mean?
The control module has registered that the gear position is incorrect. The gear position sensor sits in the control module and gives information about the selected gear. The fault is due either to the sensor being misadjusted or to an internal fault in the control module, which can stop the engine from starting or cause gear changes to fail.
Possible causes
- Misadjusted gear position sensor
- Internal fault inside the TCM
What you can do
- 1If you have a diagnostic tool: move the selector through all positions and check that the position in live data matches the display
- 2Have a workshop check the selector cable and calibrate the gear position sensor
- 3If the fault remains, have a workshop replace the control module, since a new module is supplied without software
- 4After replacement, a workshop should program the control module and check that gear changes work
Symptoms you may notice3
- The engine does not start
- Gear changes do not occur
- Harsh gear changes
What the fault can affect2
- The control module uses a basic value for adaptation
- Stored fault codes may be lost
General guidance for car owners. Diagnosis on the car can point to a different cause.