VOLVO
TCM-P072268 - Output Shaft Speed Sensor Circuit No Signal. Algorithm Based Failures. Event information
System
Transmission Control Module (TCM)
Volvo models this fault code applies to
Applies to the following models:
7 modelsS60 (2011–), S80 (2007–), V40 (2013–), V40 Cross Country (2013–), V60 (2011–), V70 (2008–), XC60 (2009–)
Show models by year and engine (16)
- Volvo S60 (2011–)2012Engine D5204T3 only · Transmission TF-80SD only
- Volvo S60 (2011–)2013–2014Engine B5204T8, B5204T9, D5204T3, D5204T7 only · Transmission TF-80SD only
- Volvo S60 (2011–)2015Engine D5204T3, D5204T7 only · Transmission TF-80SD only
- Volvo S80 (2007–)2012, 2015Engine D5204T3 only · Transmission TF-80SD only
- Volvo S80 (2007–)2013–2014Engine D5204T3, D5204T7 only · Transmission TF-80SD only
- Volvo V40 (2013–)2013All engines except: B4164T, B4164T3, D4162T · Transmission TF-80SD only
- Volvo V40 (2013–)2014All engines except: B4164T, B4164T3, B4164T4, D4162T · Transmission TF-80SD only
- Volvo V40 (2013–)2015Engine B5204T8, B5204T9, D5204T6 only · Transmission TF-80SD only
- Volvo V40 Cross Country (2013–)2013–2014All engines except: B4164T, D4162T · Transmission TF-80SD, TF-80SD AWD only
- Volvo V40 Cross Country (2013–)2015All engines except: B4164T, B4204T11, D4162T, D4204T14 · Transmission TF-80SD, TF-80SD AWD only
- Volvo V60 (2011–)2012Engine D5204T3 only · Transmission TF-80SD only
- Volvo V60 (2011–)2013–2014Engine B5204T8, B5204T9, D5204T3, D5204T7, D82PHEV only · Transmission TF-80SD only
- Volvo V60 (2011–)2015Engine B5204T9, D5204T3, D5204T7, D82PHEV, D87PHEV only · Transmission TF-80SD only
- Volvo V70 (2008–)2012Engine D5204T3 only · Transmission TF-80SD only
- Volvo V70 (2008–)2013–2015Engine D5204T3, D5204T7 only · Transmission TF-80SD only
- Volvo XC60 (2009–)2015Engine B5204T9 only · Transmission TF-80SD AWD only
What does this fault code mean?
This is an event-driven information code and does not indicate a fault in the control module where it is active. It is always set together with another fault code, and that other code shows the real fault, so deal with that one first.
Possible causes
- Higher resistance at a connection
- Output shaft speed sensor not seated correctly
- Output shaft speed sensor not working
- A fault inside the TCM itself
What you can do
- 1Read all stored codes: this code is always set together with another one, which is the real fault
- 2Deal with the other code first, following its own instructions
- 3Then clear the codes and road test; this code does not need separate work
- 4If the other code returns after the repair, have a workshop check it
Symptoms you may notice5
- Lock-up does not work
- No automatic gear change
- Gear changes are harsh or jerky
- The PURE, SAVE and AWD drive modes switch off automatically and cannot be selected
- In HYBRID mode the combustion engine runs all the time or too often
What the fault can affect1
- Electric propulsion is not possible
General guidance for car owners. Diagnosis on the car can point to a different cause.