Co powoduje kod błędu P025C?

• Most likely: Short to ground in the wiring harness between ECM and FPCM • Likely: Faulty Fuel Pump Control Module (FPCM) • Possible: Defective fuel pump relay or blown fuse supplying the module • Rare: Internal Engine Control Module (ECM) failure

Jak naprawić kod błędu P025C?

STEP 1: Check fuses related to the fuel system and FPCM. Inspect the connector at the FPCM (often located under the rear seat or near the fuel tank) for corrosion or backed-out pins. STEP 2: Measure supply voltage to the FPCM; it should match battery voltage (approx. 12.6V). Verify the ground circuit (voltage drop should be < 0.1V). STEP 3: Use an oscilloscope to probe the PWM control signal from the ECM. With ignition on/cranking, a pulse width signal should be present. If the signal wire measures 0V even when disconnected from FPCM, there is a short to ground in the harness. STEP 4: If wiring and power/ground are verified but the module does not respond to ECM commands, replace the Fuel Pump Control Module.

Powertrain (Engine & Gearbox)Standard EOBD

P025C - Fuel Pump Control Module (FPCM) - Circuit Low

Q: Co oznacza kod błędu P025C?

P025C is stored when the Engine Control Module (ECM) detects an abnormally low voltage state in the Fuel Pump Control Module (FPCM) control circuit. Modern returnless fuel systems use a variable speed pump controlled by the ECM via a PWM (Pulse Width Modulation) signal to the FPCM. If the signal circuit is shorted to ground or the voltage drops below the calibrated threshold (typically less than 0.5V when high activity is expected), the ECM monitors this as a circuit low condition. This interferes with the fuel delivery strategy and rail pressure management.

Q: Jakie są objawy kodu błędu P025C?

• Check engine light illuminated • Engine will not start • Engine hesitation or stalling during drive • Reduced engine power (Limp mode) • Rough idling

Last updated:1 February 2026

Related:Fuel Pump Control Module (FPCM), Engine Control Module (ECM), Fuel Pump, Wiring harness

System

Powertrain (Engine & Gearbox)

Related Fault Codes

P0200

Injector Circuit Malfunction

P0201

Cylinder 1 Injector Circuit Open

P0202

Injector Circuit - Cylinder 2 - Malfunction

P0203

Injector Circuit - Cylinder 3

Technical Description

P025C is stored when the Engine Control Module (ECM) detects an abnormally low voltage state in the Fuel Pump Control Module (FPCM) control circuit. Modern returnless fuel systems use a variable speed pump controlled by the ECM via a PWM (Pulse Width Modulation) signal to the FPCM. If the signal circuit is shorted to ground or the voltage drops below the calibrated threshold (typically less than 0.5V when high activity is expected), the ECM monitors this as a circuit low condition. This interferes with the fuel delivery strategy and rail pressure management.

Possible Causes

Short to ground in the wiring harness between ECM and FPCM

Faulty Fuel Pump Control Module (FPCM)

Defective fuel pump relay or blown fuse supplying the module

Internal Engine Control Module (ECM) failure

Symptoms

Check engine light illuminated

Engine will not start

Engine hesitation or stalling during drive

Reduced engine power (Limp mode)

Rough idling

Do you also have
other fault codes?

See how P025C connects with your other fault codes. Our advanced analysis tool identifies causal relationships and root causes directly.

Analyze multiple codes

P025C - Fuel Pump Control Module (FPCM) - Circuit Low

Related Fault Codes

Technical Description

Possible Causes

Symptoms

Recommended Solution

Workflow

Mechanic's Tip

Do you also have
other fault codes?

P025C - Fuel Pump Control Module (FPCM) - Circuit Low

Related Fault Codes

Technical Description

Possible Causes

Symptoms

Recommended Solution

Workflow

Mechanic's Tip

Do you also have other fault codes?

Do you also have
other fault codes?