Volvo S80 (1999–2006) – kody błędów Sterownik układu hamulcowego (BCM)
71 kodów błędów
Ten sam kod błędu może oznaczać różne rzeczy w zależności od rocznika i silnika. Dlatego każde znaczenie jest pokazane w osobnym wierszu wraz z dokładnymi samochodami, których dotyczy.
Opisy kodów błędów są dostępne po szwedzku i angielsku i są tu wyświetlane po angielsku.
| Kod | Znaczenie |
|---|---|
| BCM-0010 | Left front wheel sensor. Signal missing2002–2006 |
| BCM-0011 | Wheel sensor left front. Faulty signal2002–2006 |
| BCM-0012 | Left front wheel sensor. Faulty signal2002–2006 |
| BCM-0020 | Right front wheel sensor. Signal missing2002–2006 |
| BCM-0021 | Wheel sensor right front. Faulty signal2002–2006 |
| BCM-0022 | Right front wheel sensor. Faulty signal2002–2006 |
| BCM-0030 | Left rear wheel sensor. Signal missing2002–2006 |
| BCM-0031 | Wheel sensor left rear. Faulty signal2002–2006 |
| BCM-0032 | Left rear wheel sensor. Faulty signal2002–2006 |
| BCM-0040 | Right rear wheel sensor. Signal missing2002–2006 |
| BCM-0041 | Wheel sensor right rear. Faulty signal2002–2006 |
| BCM-0042 | Right rear wheel sensor. Faulty signal2002–2006 |
| BCM-0050 | Control module. Faulty signal2002–2006 |
| BCM-0052 | Control module. Internal fault2002–2006 |
| BCM-0057 | Power supply. Voltage too low2002–2006 |
| BCM-0058 | Power supply. Voltage too high2002–2006 |
| BCM-0061 | Brake discs. Temperature too high2002–2006 |
| BCM-0065 | Stop lamp switch. Faulty signal2002–2006 |
| BCM-0068 | Sensor power supply. Faulty signal2002–2006 |
| BCM-0070 | Power supply for the pump motor. Faulty signal2002–2006 |
| BCM-0071 | Pump motor. Signal missing2002–2006 |
| BCM-0072 | Pump motor. Mechanical fault2002–2006 |
| BCM-0074 | Hydraulic valves. Faulty signal2002–2006 |
| BCM-0076 | Control module. Faulty configuration2002–2006 |
| BCM-0080 | Lateral accelerometer. Incorrect offset value2002–2006 |
| BCM-0081 | Accelerometer. Incorrect offset value2002–2006 |
| BCM-0082 | Yaw rate sensor. Incorrect offset value2002–2006 |
| BCM-0083 | Angle of lean sensor. Incorrect offset value2005–2006 |
| BCM-0090 | Lateral accelerometer. Faulty signal2002–2006 |
| BCM-0091 | Accelerometer. Faulty signal2002–2006 |
| BCM-0092 | Yaw rate sensor. Faulty signal2002–2006 |
| BCM-0093 | Angle of lean sensor. Faulty signal2005–2006 |
| BCM-0094 | Communication between control units Communication problems with DEM2002–2006 |
| BCM-0095 | Communication between control units Communication problems with DEM2002–2006 |
| BCM-0097 | Communication between control modules. Communication problems with the central electronic module (CEM)2002–2006 |
| BCM-0100 | Communication between control modules. Communication problems with the engine control module (ECM)2002–2006 |
| BCM-0101 | Communication between control modules. Communication problems with the engine control module (ECM)2002–2006 |
| BCM-0103 | Pedal position sensor. Faulty signal2002–2006 |
| BCM-0106 | Steering wheel or wheel alignment. Incorrect steering wheel or wheel alignment2002–2006 |
| BCM-0108 | Communication between control modules. Communication with the steering angle sensor. Control module not initiated2002–2006 |
| BCM-0109 | Communication between control modules. Communication with the steering angle sensor. Internal fault2002–2006 |
| BCM-0111 | Communication between control modules. Check of the steering angle sensor tolerances has not been run2002–2006 |
| BCM-0112 | Active yaw control sensor. Sensor not calibrated2002–2006 |
| BCM-0113 | Back-up (reversing) signal. Signal missing2002–2006 |
| BCM-0114 | Communication with the active yaw control sensor. Signal missing2002–2006 |
| BCM-0115 | Communication between control modules. Communication with the steering angle sensor. Signal missing2002–2006 |
| BCM-0116 | Communication with the active yaw control sensor. Communication problems2002–2006 |
| BCM-0117 | Communication with the active yaw control sensor. An incorrect active yaw control sensor had been installed2002–2006 |
| BCM-0118 | Power supply for the active yaw control sensor. Voltage too high2002–2006 |
| BCM-0119 | Power supply for the active yaw control sensor. Voltage too low2002–2006 |
| BCM-0121 | Yaw rate sensor. Signal outside its permitted range2002–2006 |
| BCM-0123 | Active yaw control sensor. Internal fault2002–2006 |
| BCM-0125 | Lateral accelerometer. Signal outside its permitted range2002–2006 |
| BCM-0127 | Angle of lean sensor. Signal outside its permitted range2005–2006 |
| BCM-0129 | Longitudinal accelerometer. Signal outside its permitted range.2002–2006 |
| BCM-0130 | Brake pressure sensor 1. Signal too low2002–2006 |
| BCM-0133 | Brake pressure sensor 2. Signal too low2002–2006 |
| BCM-0136 | Brake pressure sensor 1 and 2. Signal outside its permitted range2002–2006 |
| BCM-0138 | Power supply for the active yaw control sensor. Faulty voltage2002–2006 |
| BCM-0139 | Pressure build-up valve, power brake booster. Signal outside its permitted range2002–2006 |
| BCM-0140 | Pedal pressure sensor. Signal outside its permitted range2002–2006 |
| BCM-0145 | Stability control. Stability control has been active for too long2002–2006 |
| BCM-0147 | Pedal position sensor. Signal outside its permitted range2002–2006 |
| BCM-0148 | Communication between control modules. Faulty configuration ID2002–2006 |
| BCM-0150 | Stop lamp switch. Signal outside its permitted range2002–2006 |
| BCM-0151 | Control module. Internal memory fault2002–2006 |
| BCM-A030 | Communication between control modules. Steering angle sensor. Initialization check not run2002–2006 |
| BCM-A031 | Communication between control modules. Steering angle sensor. Tolerance check not run2002–2006 |
| BCM-A032 | Stability function. Too long stability control2003–2006 |
| BCM-E000 | Control module communication. Faulty communication2002–2006 |
| BCM-E003 | Configuration fault. Faulty configuration2002–2006 |